Torx is better than whatever this Canadian abomination is. You’d only put pressure on the corners in a realistic setting. These would get rounded so fast unless they are massive, like on some differentials or gearbox oil drains.
Indeed torx is so good because it attempts to maximize the surface where pressure is applied to. This is good on smaller sized bolts that are more prone to being rounded, but especially amazing when removing bolts that may have been exposed and potentially corroded
Yeah, hex is very nice but torx is improvement over it.
I have not checked on it, but I’m like 97.25% sure wood screws jumped from Philips to torx however because of corrosion resistance. Hex is very easy to round already as is on smaller sizes, but even more so if the head is exposed to elements and corroded. Of course material matters a lot, but even stainless corrodes over time.
Torx has to be very, very bad condition for it to round, it’s more likely for the screw to snap
Sorry for drunk rambling but I really like bolts. And bearings for what it’s worth
Never had or seen a stripped Roberson, they are robust AF. Don’t ask me the physics. (They go deep into the screw head because of the simple shape, maybe that has part of it. And they are tapered, it’s not just a square, so they manage to grip the bit like a mofo.)
The internal hex on sway bar end links are useless after any time in the salt. Last time I had to remove them I went straight to the angle grinder and ordered a new pair. Didn’t even attempt it.
Its all fun and games until the Canadians show up.
As an American, we made a mistake in not adopting those. Torx or whatever isn’t even as good.
Oh okay. So just like with everything else we’ve failed to do
Torx is better than whatever this Canadian abomination is. You’d only put pressure on the corners in a realistic setting. These would get rounded so fast unless they are massive, like on some differentials or gearbox oil drains.
This guy mechanics
Indeed torx is so good because it attempts to maximize the surface where pressure is applied to. This is good on smaller sized bolts that are more prone to being rounded, but especially amazing when removing bolts that may have been exposed and potentially corroded
Hex was for that before.
Yeah, hex is very nice but torx is improvement over it.
I have not checked on it, but I’m like 97.25% sure wood screws jumped from Philips to torx however because of corrosion resistance. Hex is very easy to round already as is on smaller sizes, but even more so if the head is exposed to elements and corroded. Of course material matters a lot, but even stainless corrodes over time.
Torx has to be very, very bad condition for it to round, it’s more likely for the screw to snap
Sorry for drunk rambling but I really like bolts. And bearings for what it’s worth
Curious how “really like bolts. And bearings!” is working out on your Tindr profile?
Luckily I’ve never had a tinder profile. And my wife liked my nuts so we’re good
But does she like your Torx?
( ͡~ ͜ʖ ͡°)
Hex already fit that niche.
Torx was just so they could make wood screws that weren’t Robertson and it bled out from there.
Torx bits are waaaay stronger than hex. Like double the surface area and tapered to work when corroded.
My 30 year old VW axles with hex bolts were a nightmare. The new ones are all Torx or 12pt.
I ended to driving an oversized Torx but into the nearly stripped hex bolts to finally remove them.
Never had or seen a stripped Roberson, they are robust AF. Don’t ask me the physics. (They go deep into the screw head because of the simple shape, maybe that has part of it. And they are tapered, it’s not just a square, so they manage to grip the bit like a mofo.)
I’ve snapped so many Robertson bits in my life. Screws are fine.
1 5/8" cement board screws
They used to be Robertson. They switched to Torx.
Night and day difference
Like you said, they do grip like a mofo, and with an impact driver, the bits snap.
I tried dozens of different brands of bits. Even paid top dollar for special Milwaukee ones.
I was at a point where I had to pre-drill and counter sink the screws because I was breaking too many bits.
I could probably drive a torx head one through a board
Ze Germans would like a word with you.
I’ve stripped more internal hex than all other types combined
The internal hex on sway bar end links are useless after any time in the salt. Last time I had to remove them I went straight to the angle grinder and ordered a new pair. Didn’t even attempt it.
We have to go deeper.